Help us save the Earth.. One home at a time!

Insulation

Peel N Stick Tiles

$219.00
Availability: In-Stock
Quantity

Description:

Peel’n’Stick is a decorative wall covering designed to reduce sound ‘glare’ and reverberation between hard wall and ceiling surfaces and, in so doing, render a wide variety of commercial and residential settings more pleasant and productive.

Peel’n’Stick tiles are made from long lasting, environmentally benign, recycled polyester. They are moisture resistant, self-adhesive and easy to install, clean and maintain.

The texture and surface of Peel’n’Stick tiles is not only attractive in its own right but also allows pins and Velcro to turn it into a noticeboard.

Measurements/ Spec:

Each tile:

  • contains no less than 45% recycled polyester;
  • measures 600 x 600mm;
  • is 10-12mm thick;
  • comes in a palette of 40 colours;
  • typically weighs 1780 gsm;
  • is fixed by a pressure sensitive adhesive. 

 

Each pack:

  • contains 6 tiles; 
  • will cover 2.16m2 of wall.

 

Certifications

    • Fire Rating to AS ISO 9705-2003: Classification: Group 1-S;

 

Features:

Each tile is:

  • self-adhesive;
  • stain and moisture resistant;
  • fade resistant and UV stabilized;
  • available in 40 colours;
  • made from light weight, safe and easy to handle (non-toxic, non-irritating, non-allergenic) polyester;
  • manufactured from 45% post-consumer recycled material;
  • highly durable;
  • easy to clean; 
  • manufactured to ISO 9001 and ISO 14001 Quality and Environmental systems.


You Will Need:

  • a snap-off knife and blades (straight edge);
  • a hand roller or domestic rolling pin;
  • a cutting board or flat cutting surface;
  • a 1200mm level;
  • a tape measure; and
  • a pencil

 

Suitable For:

  • all residential, educational, retail and commercial interiors where sound glare may be a source of occupant discomfort.

Description:

Peel’n’Stick is a decorative wall covering designed to reduce sound ‘glare’ and reverberation between hard wall and ceiling surfaces and, in so doing, render a wide variety of commercial and residential settings more pleasant and productive.

Peel’n’Stick tiles are made from long lasting, environmentally benign, recycled polyester. They are moisture resistant, self-adhesive and easy to install, clean and maintain.

The texture and surface of Peel’n’Stick tiles is not only attractive in its own right but also allows pins and Velcro to turn it into a noticeboard.

Measurements/ Spec:

Each tile:

  • contains no less than 45% recycled polyester;
  • measures 600 x 600mm;
  • is 10-12mm thick;
  • comes in a palette of 40 colours;
  • typically weighs 1780 gsm;
  • is fixed by a pressure sensitive adhesive. 

 

Each pack:

  • contains 6 tiles; 
  • will cover 2.16m2 of wall.

 

Certifications

    • Fire Rating to AS ISO 9705-2003: Classification: Group 1-S;

 

Features:

Each tile is:

  • self-adhesive;
  • stain and moisture resistant;
  • fade resistant and UV stabilized;
  • available in 40 colours;
  • made from light weight, safe and easy to handle (non-toxic, non-irritating, non-allergenic) polyester;
  • manufactured from 45% post-consumer recycled material;
  • highly durable;
  • easy to clean; 
  • manufactured to ISO 9001 and ISO 14001 Quality and Environmental systems.


You Will Need:

  • a snap-off knife and blades (straight edge);
  • a hand roller or domestic rolling pin;
  • a cutting board or flat cutting surface;
  • a 1200mm level;
  • a tape measure; and
  • a pencil

 

Suitable For:

  • all residential, educational, retail and commercial interiors where sound glare may be a source of occupant discomfort.

**Sorry, this section is currently under maintenance. For inquiries, pop us an email at sales@ecomaster.com.au and we’ll get back to you right away.**

How long would it take to ship?

0 to 5 business days from the time of order.

The freight system at present is experiencing significant volumes which may result in delays with some deliveries. However, please note most late items arrive within 5 business days of the expected delivery date. We appreciate your patience and understanding if delays do occur.


How will the order be delivered?

Orders would be delivered through a courier.

Composition™ Peel’n’Stick Tiles feature a pressure-sensitive adhesive backing. Once applied, tiles cannot be repositioned and if removed may cause damage to paint/ plasterboard or other surfaces.

 

**PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION

 

Autex accepts no responsibility where installation instructions are not followed. These installation guidelines are meant for installers with some basic trade experience and are not a step-by-step guide. If you have any questions about the installation techniques for your particular project please contact your distributor.

 

STORAGE

Tiles must be laid flat and stored indoors on a solid and dry surface. Do not stack on a concrete floor or any other surface that emits moisture. Optimum storage conditions are 18°C with 45% - 55% relative humidity. More information about relative humidity can be found at www.bom.gov.au.

 

INSPECTION

Inspect tiles before installation where there are defects, put the tile aside and contact your Autex representative immediately. Where more than one box of tiles is required, ensure they are the same batch as indicated on the product label on each box. Batch numbers should be recorded for future reference. Once tiles are installed, they are deemed to be of an acceptable standard. No claims will be accepted.

 

ROOM TEMPERATURE/HUMIDITY

Room temperature should not be less than 18°C. Relative humidity must not be above 75% during installation.

 

SURFACE PREPARATION

GENERAL

Prior to installation ensure all surfaces are flat, dry, sound and free from dust or other contaminants.

All surfaces should be washed with a detergent that will not leave a residue and should be allowed to fully dry.

For more advice on specific applications please contact your local distributor.

We recommend that one tile be installed first to ascertain the suitability of the surface and preparation.

 

CONCRETE/RENDERED CONCRETE BLOCK AND UNEVEN SURFACES

High and low spots should be levelled to provide an even wall surface. Concrete block walls must be fully rendered. New concrete walls must have had sufficient time to cure - generally 28 days. Walls must be free of hydrostatic pressure, moisture and excessive alkalinity. Efflorescence (white powder) on the surface must be removed. In any of these instances a suitable sealer/primer must be first applied and allowed to dry. All dust must be removed by wiping down with a wet cloth and allowed to thoroughly dry. Concrete walls may be subject to condensation or low surface temperatures and must be dried/warmed prior to installation.

 

 

BEFORE INSTALLING/PRE-CONDITIONING

Prior to installing Peel’n’Stick Tiles, remove the packaging and allow the tiles to acclimatise to room temperature and humidity for approximately 1-2 hours. Ideally, both the room temperature and humidity during acclimatisation and installation should be the same as the final operating conditions.

 

INSTALLATION

Do not remove the release film on the tile until immediately prior to installation. Once the film has been removed the tile must not be exposed to any moisture or dust.

Peel’n’Stick Tiles have a pile direction indicated by the arrows on the back of the tiles. They must be laid with all the arrows in the same direction for uniformity or, as per the diagram, in a checkerboard style.

We recommend installing the tiles with the arrows pointing down. Where different colours are used together, all tiles should be laid in the same direction.

**CHANGING THE TILE DIRECTION WILL CREATE THE APPEARANCE OF SLIGHT COLOUR VARIATION

Carefully plan out your installation and ensure you have the required number of tiles for the job.

Measure and mark out on the wall the area to be covered with Peel’n’Stick Tiles. Use a spirit level to ensure your lines are horizontally and vertically straight (it’s a good idea to lay the tiles out on the floor to check the pattern first). Check the distance from the marked centre to the adjacent walls to ensure that you will have a reasonable size cut at either end. If necessary, adjust the marked centre accordingly.

Start the first tile at the junction. Remove the release film and hold the tile at an angle to the wall; apply one edge to the line and then place the tile onto the wall (Fig.1). Apply firm pressure from the centre of the tile out to the edges to ensure good adhesion.

A roller must be used to firmly push the whole surface of the tile to the wall.

Stick down the first row of tiles working to one side of the room. Subsequent tiles should be laid up against the previous tile, holding the tile at an angle to the wall and then placing down.

To cut tiles in along adjacent walls, place the tile to be cut under the next tile nearest the wall and use that tile as your guide. Peel’n’Stick Tiles can be cut with a snap-blade knife and straight edge.

Re-roll all tiles when the job is complete to ensure good adhesion. Please note: batches are sequentially numbered - the beginning of the number being the batch and the end digits being pack sequence.

Composition™ Peel’n’Stick Tiles feature a pressure-sensitive adhesive backing. Once applied, tiles cannot be repositioned and if removed may cause damage to paint/ plasterboard or other surfaces.

 

**PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION

 

Autex accepts no responsibility where installation instructions are not followed. These installation guidelines are meant for installers with some basic trade experience and are not a step-by-step guide. If you have any questions about the installation techniques for your particular project please contact your distributor.

 

STORAGE

Tiles must be laid flat and stored indoors on a solid and dry surface. Do not stack on a concrete floor or any other surface that emits moisture. Optimum storage conditions are 18°C with 45% - 55% relative humidity. More information about relative humidity can be found at www.bom.gov.au.

 

INSPECTION

Inspect tiles before installation where there are defects, put the tile aside and contact your Autex representative immediately. Where more than one box of tiles is required, ensure they are the same batch as indicated on the product label on each box. Batch numbers should be recorded for future reference. Once tiles are installed, they are deemed to be of an acceptable standard. No claims will be accepted.

 

ROOM TEMPERATURE/HUMIDITY

Room temperature should not be less than 18°C. Relative humidity must not be above 75% during installation.

 

SURFACE PREPARATION

GENERAL

Prior to installation ensure all surfaces are flat, dry, sound and free from dust or other contaminants.

All surfaces should be washed with a detergent that will not leave a residue and should be allowed to fully dry.

For more advice on specific applications please contact your local distributor.

We recommend that one tile be installed first to ascertain the suitability of the surface and preparation.

 

CONCRETE/RENDERED CONCRETE BLOCK AND UNEVEN SURFACES

High and low spots should be levelled to provide an even wall surface. Concrete block walls must be fully rendered. New concrete walls must have had sufficient time to cure - generally 28 days. Walls must be free of hydrostatic pressure, moisture and excessive alkalinity. Efflorescence (white powder) on the surface must be removed. In any of these instances a suitable sealer/primer must be first applied and allowed to dry. All dust must be removed by wiping down with a wet cloth and allowed to thoroughly dry. Concrete walls may be subject to condensation or low surface temperatures and must be dried/warmed prior to installation.

 

 

BEFORE INSTALLING/PRE-CONDITIONING

Prior to installing Peel’n’Stick Tiles, remove the packaging and allow the tiles to acclimatise to room temperature and humidity for approximately 1-2 hours. Ideally, both the room temperature and humidity during acclimatisation and installation should be the same as the final operating conditions.

 

INSTALLATION

Do not remove the release film on the tile until immediately prior to installation. Once the film has been removed the tile must not be exposed to any moisture or dust.

Peel’n’Stick Tiles have a pile direction indicated by the arrows on the back of the tiles. They must be laid with all the arrows in the same direction for uniformity or, as per the diagram, in a checkerboard style.

We recommend installing the tiles with the arrows pointing down. Where different colours are used together, all tiles should be laid in the same direction.

**CHANGING THE TILE DIRECTION WILL CREATE THE APPEARANCE OF SLIGHT COLOUR VARIATION

Carefully plan out your installation and ensure you have the required number of tiles for the job.

Measure and mark out on the wall the area to be covered with Peel’n’Stick Tiles. Use a spirit level to ensure your lines are horizontally and vertically straight (it’s a good idea to lay the tiles out on the floor to check the pattern first). Check the distance from the marked centre to the adjacent walls to ensure that you will have a reasonable size cut at either end. If necessary, adjust the marked centre accordingly.

Start the first tile at the junction. Remove the release film and hold the tile at an angle to the wall; apply one edge to the line and then place the tile onto the wall (Fig.1). Apply firm pressure from the centre of the tile out to the edges to ensure good adhesion.

A roller must be used to firmly push the whole surface of the tile to the wall.

Stick down the first row of tiles working to one side of the room. Subsequent tiles should be laid up against the previous tile, holding the tile at an angle to the wall and then placing down.

To cut tiles in along adjacent walls, place the tile to be cut under the next tile nearest the wall and use that tile as your guide. Peel’n’Stick Tiles can be cut with a snap-blade knife and straight edge.

Re-roll all tiles when the job is complete to ensure good adhesion. Please note: batches are sequentially numbered - the beginning of the number being the batch and the end digits being pack sequence.

**Sorry, this section is currently under maintenance. For inquiries, pop us an email at sales@ecomaster.com.au and we’ll get back to you right away.**

How long would it take to ship?

0 to 5 business days from the time of order.

The freight system at present is experiencing significant volumes which may result in delays with some deliveries. However, please note most late items arrive within 5 business days of the expected delivery date. We appreciate your patience and understanding if delays do occur.


How will the order be delivered?

Orders would be delivered through a courier.

Description:

Peel’n’Stick is a decorative wall covering designed to reduce sound ‘glare’ and reverberation between hard wall and ceiling surfaces and, in so doing, render a wide variety of commercial and residential settings more pleasant and productive.

Peel’n’Stick tiles are made from long lasting, environmentally benign, recycled polyester. They are moisture resistant, self-adhesive and easy to install, clean and maintain.

The texture and surface of Peel’n’Stick tiles is not only attractive in its own right but also allows pins and Velcro to turn it into a noticeboard.

Measurements/ Spec:

Each tile:

  • contains no less than 45% recycled polyester;
  • measures 600 x 600mm;
  • is 10-12mm thick;
  • comes in a palette of 40 colours;
  • typically weighs 1780 gsm;
  • is fixed by a pressure sensitive adhesive. 

 

Each pack:

  • contains 6 tiles; 
  • will cover 2.16m2 of wall.

 

Certifications

    • Fire Rating to AS ISO 9705-2003: Classification: Group 1-S;

 

Features:

Each tile is:

  • self-adhesive;
  • stain and moisture resistant;
  • fade resistant and UV stabilized;
  • available in 40 colours;
  • made from light weight, safe and easy to handle (non-toxic, non-irritating, non-allergenic) polyester;
  • manufactured from 45% post-consumer recycled material;
  • highly durable;
  • easy to clean; 
  • manufactured to ISO 9001 and ISO 14001 Quality and Environmental systems.


You Will Need:

  • a snap-off knife and blades (straight edge);
  • a hand roller or domestic rolling pin;
  • a cutting board or flat cutting surface;
  • a 1200mm level;
  • a tape measure; and
  • a pencil

 

Suitable For:

  • all residential, educational, retail and commercial interiors where sound glare may be a source of occupant discomfort.